1
The Control Room Floor / VRC help!
« on: January 26, 2009, 09:26:06 AM »
Did all that, hasn't cause me any problems so far, and i've been doing 3 hours sessions lately. Thanks guys!!
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
The Control Room Floor / VRC help!
« on: January 15, 2009, 10:27:59 PM »Quote from: Alex Ramos
what kinds of router do you have, make & model? i can give you better instructions from there
:)Ramos
Netgear WGR614v7
3
The Control Room Floor / VRC help!
« on: January 11, 2009, 10:24:33 PM »Quote from: Bob Carmona
On Netgear routers, go to LAN Set-up, then under "Address Reservation", select "Add" and reserve an IP address for the computer you are using. This forces your computer to be assigned the same address each time you start it up. Then, go to "Port Forwarding/Port Triggering", select "Add Custom Service", use TCP/UDP, enter port number, and then the IP address you resevered. You will have to do this for both ports 3290 and 3782. 3782 is for Air to Ground voice, 3290 is for Ground to Ground voice.
This should solve your problem. I was not having the static issue you are, so I do not know if this will help that.
Hope this helps,
Quote from: Alex Ramos
if your talking about how to get to the setup page of your router, do these 2 things
1: (XP) Start > Run > CMD > at the MSDOS prompt, type ipconfig
1: (vista) Start > CMD in search bar > at the MSDOS prompt, type ipconfig
2: copy down your 'Default Gateway' (usually 192.168.0.1 - but ALWAYS ends in .1)
open your favorite internet browser, and type that address you wrote down into the http bar
at this point routers can vary on model, some will pop open a name/password prompt, others will have name/password prompts in the browser. and some won't have a login at all. the website www.portforward.com at this point will usually have the default login listed if you haven't changed it.
from there find your route make and model (find your EXACT model for best results) and follow the steps from there.
more help can always be found here.
:)Ramos
Okay, got to my port forwarding/triggering now idk what the starting port is and what to put as the service name.
4
The Control Room Floor / VRC help!
« on: January 11, 2009, 06:57:36 PM »
Not sure how to get to LAN set up in the first place.
5
The Control Room Floor / VRC help!
« on: January 09, 2009, 09:35:15 AM »
Alrighty, will do!! thankss man! O, btw, will doing all this help my voice going static over time conrolling?
6
The Control Room Floor / VRC help!
« on: January 09, 2009, 09:34:00 AM »Quote from: Bob Carmona
I had this problem as well. If you are using a router, you need to forward ports 3290 and 3782 to the computer you are using. You will also need to set your router up so that your computer uses the same router IP address each time you start it up. On Netgear routers it is called IP Address Reservation and Port Forwarding/Triggering. On other routers, it may be called Static IP. Sorry not sure, but I know each router calls it something different.
For those that want to host a Teamspeak Server, you would need to forward port 8767 to the hosting computer.
Hope this helps...
Alrighty, your the man! thanks!! nooowww, i just gotta figure out how to do this 'forwarding ports'. If you can help me with that, that would be awesome. Yes, i have a netgear wireless router but my desktop is connected to it with an ethernet cable, not wireless. and how do i "set your router up so that your computer uses the same router IP address each time you start it up"? Thanks ALOT!!
7
The Control Room Floor / VRC help!
« on: January 07, 2009, 10:18:53 AM »
Hi everyone, I DID post this problem on the VRC forums and no one has gotten back to me I figured i would give it a shot here. On VRC i'll be online without any traffic for about 20mins and then someone shows up and calls me, i don't hear him so he calls me on text. All i have to do is go to my comms panel and take that freq off my PRIM then set it on again and i can hear them, idk why this does this. it's kind of like VRC went on standby cause the voice server wasn't being used. Another thing, if my voice IS working, after about 20mins of controlling my voice goes completly static to pilots, I have to completly shut down VRC and start it up again to fix this. It is VERY annoying when you are busy on center!! Then when i fix the problem, it does it again in about 15-20mins!!
I would GREATLY appreciate ANY help!!!!!!!!!!!!!!!!!!!!!!!
Thanks!
I would GREATLY appreciate ANY help!!!!!!!!!!!!!!!!!!!!!!!
Thanks!
Pages: [1]